Search for dissertations about: "deformation factor"

Showing result 1 - 5 of 92 swedish dissertations containing the words deformation factor.

  2. 1. Torque and Angle Controlled Tightening of Bolted Joints

    Author : Göran Toth; Chalmers University of Technology; []
    Keywords : TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; torque controlled tightening; deformation parameters; momentary elongation; deformation factor; torque; Bolted screwed joints; spring characteristic; Torx; torque and angle controlled tightening; hexalobular; final torque; snug torque; Taylor’s series expansions; preload; plastic deformation; permanent elongation; yield; friction diameter; plastic spring constant; clevis; turn-of-nut method; bearing surface pressure; twisting; Monte-Carlo simulations;

    Abstract : Reduced weight and fuel consumption, improved reliability and engine performance are the main requirements in the automotive industry of today. These requirements demand robust and optimized bolted joints, where a high amount of preload obtained by effective utilisation of the bolt is essential. READ MORE

  4. 2. Microstructure and plastic deformation of textured CVD alumina coatings

    Author : Siamak Shoja; Chalmers University of Technology; []
    Keywords : TEKNIK OCH TEKNOLOGIER; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; ENGINEERING AND TECHNOLOGY; α-Al2O3; Texture; Coatings; TKD; Plastic deformation; Deformation mechanisms; Electron microscopy; CVD;

    Abstract : It is known that the wear performance of α-alumina coatings produced by chemical vapor deposition (CVD) is significantly influenced by the type and degree of texture. However, the main reasons behind this behavior are not fully understood. This thesis contains studies of two related topics for increasing the understanding of α-alumina coatings. READ MORE

  5. 3. Influences of the Graphite Phase on Elastic and Plastic Deformation Behaviour of Cast Irons

    Author : Torsten Sjögren; Ingvar L. Svensson; Sten Johansson; Jorge Sikora; Linköpings universitet; []
    Keywords : ENGINEERING AND TECHNOLOGY; TEKNIK OCH TEKNOLOGIER; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Cast iron; Flake graphite; Compacted graphite; Spheroidal graphite; Elastic deformation; Plastic deformation; Modulus of elasticity; Graphite modulus of elasticity; Strength coefficient; Strain hardening exponent; Acoustic emission; Construction materials; Konstruktionsmaterial;

    Abstract : The amount and morphology of the graphite phase largely controls the resulting properties of cast iron. For instance, in flake graphite cast irons the mechanical properties are low while the thermal conductivity is high. READ MORE

  6. 4. Effects of deep excavations in soft clay on the immediate sourroundings-Analysis of the possibility to predict deformations and reactions against the retaining system

    Author : Anders Kullingsjö; Chalmers University of Technology; []
    Keywords : TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; MIT-S1; Sheet pile wall; Soil-structure interaction; Strain; Stress; Ground surface settlement; Finite element method; Case history; Shear test; Shear strength; Pore pressure; Analysis; Constitutive models; Plane strain; Elastoplasticity; Laboratory tests; Factor of safety; Stiffness; e-ADP; Earth pressure; Anisotropy; Soft Clay; Deep excavation; Retaining wall; Shear stress; Deformation;

    Abstract : When excavating in an urban environment, the evaluation of the magnitude and distribution of ground movements is an important part of the design process, since excessive movements can damage adjacent buildings and utilities. In order to minimize movement of the surrounding soil, a retaining wall support system is used for deep excavations to provide lateral support. READ MORE

  7. 5. Torque and angle controlled tightening over the yield point of a screw

    Author : Göran Toth; Chalmers University of Technology; []
    Keywords : clevis; permanent elongation factor; Monte-Carlo simulations; bolted screwed joints; final preload; torque and angle controlled tightening; extreme-value method; plastic deformation; Taylor s series expansions; plastic spring constant of the screw; yield; elastic angle; momentary elongation factor; snug torque; torque controlled tightening; final torque; turn-of-nut method;

    Abstract : .... READ MORE