Search for dissertations about: "solidification modelling"

Showing result 1 - 5 of 28 swedish dissertations containing the words solidification modelling.

  2. 1. Metal Expansion Penetration During Solidification of Grey Cast Iron

    Author : Izudin Dugic; Linköpings universitet; []
    Keywords : TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Grey cast iron; solidification; solidification modelling; graphite expansion; molar volume; casting simulation; thennal analysis; thermoanalysis cup; casting temperature; inoculation; inoculant; meta! expansion penetration; eutectic cell size.; TECHNOLOGY; TEKNIKVETENSKAP;

    Abstract : The meta! expansion penetration has been examined experimentally. The whole casting process was simulated using a commercial software, in order to investigate the solidification characteristics and the pore formation in the casting studied. READ MORE

  4. 2. Microstructure Formation During Solidification and Solid State Transformation in Compacted Graphite Iron

    Author : Mathias König; Magnus Wessén; Ingvar L. Svensson; Jorge Sikora; Jönköping University; []
    Keywords : TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Cast Iron; CGI; Microstructure Formation; Mechanical Properties; Modelling; Solidification; Solid State Transformation;

    Abstract : Compacted graphite iron (CGI) is rapidly becoming an attractive alternative material for engine components in the automotive industry, replacing lamellar graphite iron (LGI) in applications where high mechanical strength is desired. However, the gain in mechanical strength comes with a cost; thermal conductivity, process control and machining are three areas that are more challenging for CGI. READ MORE

  5. 3. The mechanisms of metal expansion penetration during solidification of grey cast iron

    Author : Izudin Dugic; Preben Norgaard Hansén; Linköpings universitet; []
    Keywords : TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Grey cast iron; solidification; solidification modelling; graphite expansion; molar volume; casting simulation; thermal analysis; thermoanalysis cup; casting temperature; inoculation; inoculant; metal expansion penetration; eutectic cell size; primary austenite; austenite grain; TECHNOLOGY; TEKNIKVETENSKAP;

    Abstract : The production of high quality castings requires the casting surface to be clean and free from defects. One type of defect often found is caused by metal penetration into the sand mould. READ MORE

  6. 4. Density variations during solidification of lamellar graphite iron

    Author : Kristina Hellström; Attila Diószegi; Lucian Diaconu; Primoz Mrvar; Jönköping University; []
    Keywords : TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; density; grey cast iron; measurements; modelling; densitet; gjutjärn; mätning; simulering;

    Abstract : .... READ MORE

  7. 5. Microstructure and properties of welds in the lean duplex stainless steel LDX 2101

    Author : Elin M. Westin; John Ågren; Hannu Hänninen; KTH; []
    Keywords : TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Duplex stainless steel; welding; HAZ; nitrogen; manganese; microstructure; austenite formation; phase balance; precipitates; element distribution; segregation; depletion; solidification; pitting corrosion resistance; solidification; element loss; evaporation; deposition; weld oxide; thermo-mechanical simulation; thermodynamic modelling; EPMA; XPS; post-weld cleaning; pickling; Metallurgical process and manufacturing engineering; Metallurgisk process- och produktionsteknik;

    Abstract : Duplex stainless steels can be very attractive alternatives to austenitic grades due to their almost double strength at equal pitting corrosion resistance. When welding, the duplex alloys normally require addition of filler metal, while the commodity austenitic grades can often be welded autogenously. READ MORE